插销牢固度试验装置 FP-1 插销牢固度测试
信息ID:48971422
产品详情有图信息
- 信息类型:求购
- 价格：100元
- 所属行业：报警消防装备设备
- 数量：1套
- 发布时间：2018-12-19
- 所在地区：广东佛山
详细介绍：
插销牢固度试验装置FP-1
Apparatus to verify the fixation of pins in the body of the plug FP-1
产品概述：本装置符合GB2099.1-2008图30、IEC884-1图30、BS1363标准的要求，适用于对插头插销的牢固度进行检验。
工位：一位；
砝码：50N1个、20N2个、30N1个、4N1个；
插座夹具：配GB/BS/USA插座等6个。
Products Information
Product details:Model FP-1.
The plug is placed on a rigid steel plate provided with holes suitable for the pins of the plug.
The distances between the centres of the holes shall be the same as the distances between the centres of the circle circumscribed around the cross-sectional area of each pin in the standard sheet of the plug.
Each hole shall have a diameter equal to that of the circle circumscribed around the cross-sectional area of the pin plus (6 ± 0,5) mm.
The plug is positioned on the steel plate in such a way that the centres of the circles circumscribing the pins coincide with the centres of the holes.
A pull P equal to the maximum withdrawal force as given in table 16, is applied, without jerks, for 1 min on each pin in turn, in the direction of the longitudinal axis of the pin.
The pull is applied within a heating cabinet at a temperature of (70 ± 2) °C, 1 h after the plug has been placed in the heating cabinet.
After the test, the plug is allowed to cool down to ambient temperature.it shall be verified that no pin has been displaced in the body of the plug by more than 1 mm.
No.of Test Station: 1
Weight: 50N*1,20N*2,30N*1,4N*1
Standard Socked: BS socked*1,USA socked*1
Conform to standard: IEC 60884-1 Fig30, VDE0620, BS1363
Apparatus to verify the fixation of pins in the body of the plug FP-1
产品概述：本装置符合GB2099.1-2008图30、IEC884-1图30、BS1363标准的要求，适用于对插头插销的牢固度进行检验。
工位：一位；
砝码：50N1个、20N2个、30N1个、4N1个；
插座夹具：配GB/BS/USA插座等6个。
Products Information
Product details:Model FP-1.
The plug is placed on a rigid steel plate provided with holes suitable for the pins of the plug.
The distances between the centres of the holes shall be the same as the distances between the centres of the circle circumscribed around the cross-sectional area of each pin in the standard sheet of the plug.
Each hole shall have a diameter equal to that of the circle circumscribed around the cross-sectional area of the pin plus (6 ± 0,5) mm.
The plug is positioned on the steel plate in such a way that the centres of the circles circumscribing the pins coincide with the centres of the holes.
A pull P equal to the maximum withdrawal force as given in table 16, is applied, without jerks, for 1 min on each pin in turn, in the direction of the longitudinal axis of the pin.
The pull is applied within a heating cabinet at a temperature of (70 ± 2) °C, 1 h after the plug has been placed in the heating cabinet.
After the test, the plug is allowed to cool down to ambient temperature.it shall be verified that no pin has been displaced in the body of the plug by more than 1 mm.
No.of Test Station: 1
Weight: 50N*1,20N*2,30N*1,4N*1
Standard Socked: BS socked*1,USA socked*1
Conform to standard: IEC 60884-1 Fig30, VDE0620, BS1363
